Difference between revisions of "3 Phase IPR"

From wiki.pengtools.com
Jump to: navigation, search
(→‎Three-phase Inflow Performance Relationship)
(→‎3 Phase IPR calculation example)
 
(90 intermediate revisions by the same user not shown)
Line 1: Line 1:
 
__TOC__
 
__TOC__
 
==Three-phase Inflow Performance Relationship==
 
==Three-phase Inflow Performance Relationship==
−
[[File:Inflow Performance Relationship.png|thumb|right|400px|link=https://www.pengtools.com/pqPlot|Inflow Performance Relationship Curve]]
+
[[File:3 Phase IPR Curve.png|thumb|right|400px|3 Phase IPR Curve <ref name=KermitBrown1984/>]]
  
−
[[3 Phase IPR]] calculates IPR curve for oil wells producing water.
+
[[3 Phase IPR]] is an [[IPR]] curve calculated on the basis of total barrels of produced fluid, including gas.
  
−
[[3 Phase IPR]] solution was derived by Petrobras based on combination of [[Vogel's IPR]] equation for oil flow and constant productivity for water flow <ref name=KermitBrown1984/>.
+
[[3 Phase IPR]] curve is used in [[:Category:PumpDesign|Pump Design]] software for pump sizing.
  
 
==Math and Physics==
 
==Math and Physics==
−
===Oil well IPR equation===
+
The volume of 1 stb of liquid plus associated gas at any pressure and temperature is given by<ref name=KermitBrown1984/>:
−
*[[Darcy's law]] equation for the single-phase flow of incompressible liquid:
+
:<math> VF=WCUT\ B_w + (1-WCUT)\ B_o + (GLR\ - (1-WCUT)R_s - WCUT\ R_{sw})B_g</math> <ref name=KermitBrown1984/>
  
−
:<math> q = \frac{kh}{141.2 B \mu}\ (\bar{P} - P_{wf}) J_D</math>
 
  
−
*[[Vogel's IPR]] two-phase flow equation (oil + gas) and it's combination with single phase liquid
+
The total volume of produced fluid rate (liquid plus gas) at any conditions of pressure and temperature:
−
*[[3 Phase IPR]] three-phase flow equation (oil + gas + water)
+
:<math> V=q_{t_{sc}} \times VF</math> <ref name=KermitBrown1984/>
  
−
===Gas well IPR equation ===
+
<math> q_{t_{sc}} </math> is calculated as usual using:
−
*[[Darcy's law]] gas inflow equation:
+
:*[[Vogel's IPR]] equation
 +
:*[[Composite IPR]] equation
  
−
:<math>q_g=\frac{kh}{1422 \times 10^3\ T_R}\ (P_{\bar{P}} - P_{P_{wf}})\ J_D </math>
+
==[[3 Phase IPR]] calculation example==
 +
Following the well #1 example given by Brown<ref name=KermitBrown1984 />on Figure 5.8, page 191:
  
−
*C and n equation
+
''In progress ...''
−
 
 
−
==IPR calculator software==
 
−
*[[:Category:PQplot | PQplot]] nodal analysis software is used to calculate the [[IPR]] curves. [[:Category:PQplot | PQplot]]  is available online at [https://www.pengtools.com www.pengtools.com].
 
−
*Excel
 
−
*other
 
  
 
== Nomenclature  ==
 
== Nomenclature  ==
−
:<math> B </math> = formation volume factor, bbl/stb
+
:<math> B</math> = volume factor, bbl/stb oil; bbl/scf gas
−
:<math> J_D </math> = dimensionless productivity index, dimensionless
+
:<math> GLR</math> = gas liquid ratio, scf / bbl
−
:<math> kh</math> = permeability times thickness, md*ft
+
:<math> q </math> = flowing rate, stb/d
−
:<math> \bar{P} </math> = average reservoir pressure, psia
+
:<math> R</math> = solution gas ration, scf / stb
−
:<math> P_{\bar{P}} </math> = average reservoir pseudopressure, psia<sup>2</sup>/cP
+
:<math> V </math> = total volume of produced fluid rate (inducing gas), bbl/d
−
:<math> P_{wf} </math> = well flowing pressure, psia
+
:<math> VF </math> = volume factor, bbl/stb
−
:<math> P_{P_{wf}} </math> = average well flowing pseudopressure, psia<sup>2</sup>/cP
+
:<math> WCUT</math> = water cut, fraction
−
:<math> q </math> = flowing rate, stb/d
+
===Subscripts===
−
:<math> q_g </math> = gas rate, MMscfd
+
:g = gas<BR/>
−
:<math> T </math> = temperature, °R
+
:o = oil<BR/>
−
 
+
:sc = standard conditions<BR/>
−
===Greek symbols===
+
:t = total<BR/>
−
 
+
:w = water<BR/>
−
:<math> \mu </math> = viscosity, cp
 
  
−
=== References ===
+
== References ==
 
<references>
 
<references>
−
<ref name=Vogel>{{cite journal
+
<ref name= KermitBrown1984 >{{cite book
−
  |last1= Vogel |first1=J. V.
+
  |last1= Brown |first1= Kermit
−
  |title=Inflow Performance Relationships for Solution-Gas Drive Wells
+
  |title=The Technology of Artificial Lift Methods. Volume 4. Production Optimization of Oil and Gas Wells by Nodal System Analysis
−
  |journal=Journal of Petroleum Technology
+
  |publisher=PennWellBookss
−
  |volume=20
+
  |date=1984
−
  |number=SPE-1476-PA
+
  |place=Tulsa, Oklahoma
−
|date=1968
 
 
}}</ref>
 
}}</ref>
  
Line 58: Line 52:
  
 
==See also==
 
==See also==
−
:[[141.2 derivation]]<BR/>
+
:[[IPR]]<BR/>
 +
:[[Vogel's IPR]]<BR/>
 +
:[[Composite IPR]]<BR/>
 
:[[Darcy's law]]<BR/>
 
:[[Darcy's law]]<BR/>
−
:[[JD]]<BR/>
 
−
:[[Production Potential]]
 
  
 
{{#seo:
 
{{#seo:
−
|title=Inflow Performance Relationship
+
|title=3 Phase IPR curve
 
|titlemode= replace
 
|titlemode= replace
 
|keywords=Inflow Performance Relationship, nodal analysis, IPR curve, IPR calculator
 
|keywords=Inflow Performance Relationship, nodal analysis, IPR curve, IPR calculator
−
|description=IPR curve formula for well performance.
+
|description=Three-phase inflow performance relationship for total volume of produced rate (including free gas).
 
}}
 
}}
  
 
[[Category:PQplot]]
 
[[Category:PQplot]]
−
[[Category:pengtools]]
+
[[Category:PumpDesing]]

Latest revision as of 07:51, 17 April 2019

Three-phase Inflow Performance Relationship

3 Phase IPR Curve [1]

3 Phase IPR is an IPR curve calculated on the basis of total barrels of produced fluid, including gas.

3 Phase IPR curve is used in Pump Design software for pump sizing.

Math and Physics

The volume of 1 stb of liquid plus associated gas at any pressure and temperature is given by[1]:

VF=WCUT\ B_w + (1-WCUT)\ B_o + (GLR\ - (1-WCUT)R_s - WCUT\ R_{sw})B_g [1]


The total volume of produced fluid rate (liquid plus gas) at any conditions of pressure and temperature:

V=q_{t_{sc}} \times VF [1]

q_{t_{sc}} is calculated as usual using:

3 Phase IPR calculation example

Following the well #1 example given by Brown[1]on Figure 5.8, page 191:

In progress ...

Nomenclature

B = volume factor, bbl/stb oil; bbl/scf gas
GLR = gas liquid ratio, scf / bbl
q = flowing rate, stb/d
R = solution gas ration, scf / stb
V = total volume of produced fluid rate (inducing gas), bbl/d
VF = volume factor, bbl/stb
WCUT = water cut, fraction

Subscripts

g = gas
o = oil
sc = standard conditions
t = total
w = water

References

  1. ↑ 1.0 1.1 1.2 1.3 1.4 Brown, Kermit (1984). The Technology of Artificial Lift Methods. Volume 4. Production Optimization of Oil and Gas Wells by Nodal System Analysis. Tulsa, Oklahoma: PennWellBookss. 

See also

IPR
Vogel's IPR
Composite IPR
Darcy's law
Retrieved from "https://wiki.pengtools.com/index.php?title=3_Phase_IPR&oldid=6158"