Difference between revisions of "3 Phase IPR"

From wiki.pengtools.com
Jump to: navigation, search
(→‎Three-phase Inflow Performance Relationship)
(→‎Three-phase Inflow Performance Relationship)
Line 5: Line 5:
 
[[3 Phase IPR]] is an [[IPR]] curve calculated on the basis of total barrels of produced fluid, including gas.
 
[[3 Phase IPR]] is an [[IPR]] curve calculated on the basis of total barrels of produced fluid, including gas.
  
−
[[3 Phase IPR]] used in [[:Category:PumpDesign|Pump Design]] software for pump sizing.
+
[[3 Phase IPR]] curve is used in [[:Category:PumpDesign|Pump Design]] software for pump sizing.
  
 
==Math and Physics==
 
==Math and Physics==

Revision as of 06:55, 17 April 2019

Three-phase Inflow Performance Relationship

3 Phase IPR Curve [1]

3 Phase IPR is an IPR curve calculated on the basis of total barrels of produced fluid, including gas.

3 Phase IPR curve is used in Pump Design software for pump sizing.

Math and Physics

Total flow rate equations:

For Pb < Pwf < Pr

For pressures between reservoir pressure and bubble point pressure:

q_t =J (P_r - P_{wf}) [1]

For PwfG < Pwf < Pb

For pressures between the bubble point pressure and the flowing bottom-hole pressures:

q_t =\frac{-C+\sqrt{C^2-4B^2D}}{2B^2}\ for B \ne 0[1]
q_t =D/C\ for B = 0[1]

where:

A=\frac{P_{wf}+0.125F_oP_b-F_wP_r}{0.125F_oP_b}[1]
B=\frac{F_w}{0.125F_oP_bJ}[1]
C=2AB+\frac{80}{q_{o_{max}}-q_b}[1]
D=A^2-80\frac{q_b}{q_{o_{max}}-q_b}-81[1]

For 0 < Pwf < PwfG

q_t =\frac{P_{wfG}+q_{o_{max}}tan(\beta)-P_{wf}}{tan(\beta)}[1]

where:

tan(\beta) = CD/CG [1]
CD = F_w\frac{0.001q_{o_{max}}}{J}+F_o0.125P_b \left ( -1+\sqrt{81-80 \frac{0.999q_{o_{max}}-q_b}{q_{o_{max}}-q_b}} \right)[1]
CG = 0.001 q_{o_{max}}[1]

And

P_{wfG}=F_w \left ( P_r - \frac{q_{o_{max}}}{J}\right )[1]
q_{o_{max}}=q_b+\frac{JP_b}{1.8}[1]

3 Phase IPR calculation example

Figure.1 3 Phase IPR calculation example

Following the example problem #21, page 33 [1]:

Given:

P_r = 2550 psi
P_b = 2100 psi

Test data:

P_{wf} = 2300 psi
q_t = 500 b/d

Calculate:

Determine the 3 Phase IPR curves for Fw=0, 0.25, 0.5, 0.75, and 1.

Solution:

The problem was run through PQplot software for different values of watercut.

Result 3 Phase IPR curves are shown on Fig.1. Points indicate results obtained by Brown [1].

The PQplot model from this example is available online by the following link: 3 Phase IPR calculation example

Nomenclature

A, B, C, D, tan(\beta), CD, CG = calculation variables
F_o = oil fraction, fraction
F_w = water fraction, fraction
J = productivity index, stb/d/psia
P = pressure, psia
q = flowing rate, stb/d

Subscripts

b = at bubble point
max = maximum
o = oil
r = reservoir
t = total
wf = well flowing bottomhole pressure
wfG = well flowing bottomhole pressure at point G

References

  1. ↑ 1.00 1.01 1.02 1.03 1.04 1.05 1.06 1.07 1.08 1.09 1.10 1.11 1.12 1.13 1.14 1.15 Brown, Kermit (1984). The Technology of Artificial Lift Methods. Volume 4. Production Optimization of Oil and Gas Wells by Nodal System Analysis. Tulsa, Oklahoma: PennWellBookss. 

See also

IPR
Vogel's IPR
Darcy's law
Retrieved from "https://wiki.pengtools.com/index.php?title=3_Phase_IPR&oldid=6128"