Difference between revisions of "OnPlan Comparison Study 2 Warpinski"
(→onPlan Models) |
(→onPlan Models) |
||
| Line 94: | Line 94: | ||
[https://www.pengtools.com/onPlan?paramsToken=f65a7c7896ff5a373156e9ef037aa57c Warpinski Case 2] | [https://www.pengtools.com/onPlan?paramsToken=f65a7c7896ff5a373156e9ef037aa57c Warpinski Case 2] | ||
| − | [[File:Warpinski Case 3.png|600px| Warpinski Case 3]] | + | [[File:Warpinski Case 3.png|600px| Warpinski Case 3 (3-Layer 200cp)]] |
| − | [https://www.pengtools.com/onPlan?paramsToken=6649e6453a5f3c3bebac077d1090c5d3 Warpinski Case 3] | + | [https://www.pengtools.com/onPlan?paramsToken=6649e6453a5f3c3bebac077d1090c5d3 Warpinski Case 3 (3-Layer 200cp)] |
Revision as of 07:47, 31 October 2018
Contents
Brief
The case study is based on Warpinski [1] paper published in 1994.
The onPlan calculates 6 cases described in the paper and shows good agreement in results.
Inputs
Paper Summary
This study is a comparison of hydraulic fracture models run using test data from the GRI Staged Field Experiment No. 3. Models compared include 2D, pseudo-3D, and 3D codes, run on up to eight different cases. Documented in this comparison are the differences in length, height, width, pressure, and efficiency. The purpose of this study is to provide the completions engineer with a practical comparison of the available models so that rational decisions can be made as to which model is optimal for a given application.— Warpinski et al [1]
Simulators
Planar 3D models:
- TerraFrac of TerraTek Inc.
- HYFRAC3D by S.H. Advani of Lehigh U. - Planar 3D model
- GOHFER by by Marathon Oil Co. - a unique finite-difference simulator
Planar pseudo-3D models:
- STIMPLAN of NSI Inc.
- ENERFRAC of Shell
- TRIFRAC of S.A. Holditch & Assocs. Inc.
- FRACPRO of Reservoir Engineering Systems (RES) Inc.
- MFRAC-II of Meyer& Assocs.
Classic Perkins-Kern-Nordgren (PKN) and Geertsma-deKlerk (GDK) model:
- PROP of Halliburton
- Chevron 2D model
- Conoco 2D model
- Shell 2D model
- pseudo-3D models run in constant-height mode
Cases
| CASE | 1 | 2 | 3 | 4 | 5 | 6 |
|---|---|---|---|---|---|---|
| Formation Properties | ||||||
| Resesvoir and rock data | Single-Layer | Single-Layer | 3-Layer | 3-Layer | 5-Layer | 5-Layer |
| Fluid Properties | ||||||
| Viscosity, cP | 200 | 200 | 200 | |||
| K, (lbf-sec^n)/ft^2 | 0.5 | 0.5 | 0.5 | |||
| n | 0.06 | 0.06 | 0.06 | |||
| Leak-off, ft/min^0.5 | 0.00025 | 0.00025 | 0.00025 | 0.00025 | 0.00025 | 0.00025 |
| Spurt loss, gal/ft^2 | 0 | 0 | 0 | 0 | 0 | 0 |
| Other Data | ||||||
| Pumping rate, bbl/min | 50 | 50 | 50 | 50 | 50 | 50 |
| Pumping volume, bbl | 10000 | 10000 | 10000 | 10000 | 10000 | 10000 |
| Pupming time, min | 200 | 200 | 200 | 200 | 200 | 200 |
| Proppant | None | None | None | None | None | None |
Rock and reservoir data:
| Interval | Depth (ft) | Zone Thickness (ft) | In Situ Stress (psi) | Poisson's Ratio | Young's Modulus (10^6 psi) | Fracture Toughness (psi/in^0.5) |
|---|---|---|---|---|---|---|
| Single-Layer Case | ||||||
| 1 | 9170-9340 | 170 | 5700 | 0.21 | 8.5 | 2000 |
| 3-Layer Case | ||||||
| 1 | 8990-9170 | 180 | 7150 | 0.3 | 6.5 | 2000 |
| 2 | 9170-9340 | 170 | 5700 | 0.21 | 8.5 | 2000 |
| 3 | 9340-9650 | 310 | 7350 | 0.29 | 5.5 | 2000 |
| 5-Layer Case | ||||||
| 1 | 8990-9170 | 180 | 7150 | 0.3 | 6.5 | 2000 |
| 2 | 9170-9340 | 170 | 5700 | 0.21 | 8.5 | 2000 |
| 3 | 9340-9380 | 40 | 7350 | 0.26 | 5.4 | 2000 |
| 4 | 9380-9455 | 75 | 5800 | 0.2 | 7.9 | 2000 |
| 5 | 9455-9650 | 195 | 8200 | 0.3 | 4.0 | 2000 |
Perforations data:
The well was perforated between 9225 to 9250 ft and 9285 to 9330 ft.
Comparison
The fracture net pressure, half-length, width and height predicted by different simulators[1] are plotted below in dots. The overlapped onPlan fracture net pressure, half-length, width and height shown as lines are in a good agreement with the simulation data.
 Case 1 (Single-Layer 200cp). Net Pressure |  Case 1 (Single-Layer 200cp). Half-length |  Case 1 (Single-Layer 200cp). Width |  Case 1 (Single-Layer 200cp). Height |
 Case 2 (Single-Layer K&n). Net Pressure |  Case 2 (Single-Layer K&n). Half-length |  Case 2 (Single-Layer K&n). Width |  Case 2 (Single-Layer K&n). Height |
 Case 3 (3-Layer 200cp). Net Pressure |  Case 3 (3-Layer 200cp). Half-length |  Case 3 (3-Layer 200cp). Width |  Case 3 (3-Layer 200cp). Height |
onPlan Models
The onPlan models from this study are available online at www.pengtools.com by the following links:
Warpinski Case 3 (3-Layer 200cp)
Note that evaluation access is required to open the models. Please contact us to get evaluation access.
References
- ↑ 1.0 1.1 1.2 N.R., Warpinski; Z.A., Moschovidis; C.D., Parker; I.S., Abou-Sayed (1994). "Comparison Study of Hydraulic Fracturing Models—Test Case: GRI Staged Field Experiment No. 3 (includes associated paper 28158 )" (SPE-25890-PA). Society of Petroleum Engineers.
